Memory (DIMM)
1818-8505 64MB, 133MHz, 3.3v, 144-pin SDRAM SO-DIMM memory module
C7779-60269 64MB SO-DIMM memory module - Can be installed ONLY into the formatter board
C7779-60270 128MB SO-DIMM memory module - Can be installed ONLY into the formatter board
Memory (SIMM)
1818-5624 4MB, 70nS DRAM SIMM memory module
D2297-69001 16MB, 70nS, 36-bit SIMM memory module
D2298-69001 32MB, 70nS, 36-bit SIMM memory module Part D2298-69001 is no longer supplied. Please order the replacement, D3578-69001
D2975-69001 8MB, 70nS, 36-bit parity SIMM memory module
D3577-69001 8MB, 70nS, 36-bit parity SIMM memory module
D3578-69001 32MB, 70nS, 36-bit parity SIMM memory module
D3578A 32MB, 70nS, 36-bit parity SIMM memory module
Memory Module
J2547-61001 Flash SIMM memory module - For upgrading older JetDirect EX Ethernet interface modules to the latest firmware revision - For automatic multiprotocol switching Part J2547-61001 is no longer supplied. Please order the replacement, J3265-69001
PC Board (Interface)
J4167-69001 JetDirect 610N token ring LAN interface board - DB-9 and RJ-45 connectors
Cable
C4713-60181 Carriage assembly trailing cable (D-size) - Has 60-pin (F) connectors - 1.6m (5.2ft) long
C4713-60182 Flexible stranded wire cable - 12.5cm (4.9in) long
Cable (Interface)
8121-0868 Universal Serial Bus (USB) interface cable (Black) - Type 'A' connector to type 'B' connector - 1.83m (6.0ft) long
Cable Kit
C7769-60298 Ribbon cable kit - Includes installation instructions and ribbon cable with ferrite - Cable has 40 pin (F) connectors - 1.6m (5.1ft) long
C7769-60305 Carriage assembly trailing cable kit - Includes installation instructions, trailing cables, two mounting clips, and a ferrite - Cables are 1.4m (4.7ft) long with 30 pin (M) edge connectors - For use with 24-inch plotters
Belt
CH538-67018 Belt assembly - Includes belt tensioner - For 44-inch plotters
Bushing
Q5669-60687 Carriage rear bushing
Carriage
CH538-67044 Carriage with cutter Assembly - For the Designjet T770/T790/T1200/T1300/T2300 printer series Part CH538-67044 is no longer supplied. Please order the replacement, CR647-67025
Cover
CK837-67002 Carriage cover - For the Designjet printers
CK837-67003 Carriage PCA covers - For Designjet printers Part CK837-67003 is no longer supplied. Please order the replacement, CK837-67028
Cutter
CN727-67023 Cutter assembly - Includes screw
Ink Tubes Assembly
CH538-67025 Ink supply tubes - Includes trailing cable - For use with Designjet printers Part CH538-67025 is no longer supplied. Please order the replacement, CR649-67004
Latch
CK837-67001 Carriage latch - For the Designjet printers
PC Board
CK837-67005 Carriage PCA - Controls movement of carriage assembly - For Designjet printers
Sensor
Q6683-67004 Line sensor - Detects paper width and skew - Measures calibration accuracy and printhead alignment Part Q6683-67004 is no longer supplied. Please order the replacement, CR647-67024
Strip
CK839-67005 Encoder strip - Includes the encoder strip spring and nut - For Designjet printers
Cover
CH538-67012 Back cover - For the Designjet T1200/T770 printer series
CH538-67013 Left cover assembly - Includes the ink door - For the Designjet T1200 printer series
CH538-67014 Right cover - For the Designjet T1200 printer series
CH538-67026 Top cover - For the 44-inch Designjet T1200 printer series
CH539-67005 Left cover assembly - Includes the ink door - For the Designjet T770 printer series
CH539-67006 Right cover - For the Designjet T770 printer series
CH539-67011 Top cover - For the 44-inch Designjet T770 printer series
Q6687-60064 Front cover assembly - For 44-inch plotters
Door
CH538-67017 Left ink cartridge door - For Designjet printers
CH538-67045 Right ink cartridge door - For the Designjet T1200/T770 printer series
CH539-67008 Left ink cartridge door - For the Designjet T770 printer series
Front Panel
CH538-67032 Front panel - For the 44-inch Designjet T1200 printer series
Hardware
CH538-67022 Converger assembly - For the 44-inch Designjet printers
CH539-67010 Converger CR assembly - For the Designjet T770 printer series
Panel
CH538-67005 Left side panel - For Designjet printers
CH539-67002 Left side panel - For 24-inch plotters
Paper Path Module
CH538-67039 Clean out - For the 44-inch Designjet T1200/T770 printer series
Platen
Q6659-60089 Output platen assembly - For 44-inch plotters
Sensor
CH538-67071 Window position sensor - Includes shield
Q5669-67068 Out of paper sensor (OOPS)
Trim
Q6675-60109 Left and right trim assemblies
Window
CH538-67030 Front panel window cover - For 44-inch plotters
Belt
C4705-60082 Carriage belt (D-size) - Long/wide belt attached to the carriage
C7769-60182 Carriage belt - Drives the carriage assembly - For use with 24-inch plotters
C7769-60392 Carriage belt (24-inch)
Bushing
C7769-60169 Cutter bushing
Cam
C2847-20005 Pinch arm bar cam (D-size) - Long rod from left to right side of printer - Used to lift the pinch arms
C3190-40020 Bail lift cam - Mounted behind the bail engaging lever support
Clutch
C4713-60129 Overdrive clutch assembly - Small, wide gear near overdrive gear - Held in place with a retaining E-ring
Encoder
C7769-60254 Encoder disk assembly - Helps provide position the information of the paper
End Cap
C3174-40011 Spindle end cap (2-inch)
Fan
C7769-60407 Vacuum fan assembly
Gear
C1633-40027 Bail engaging lever gear
C3190-40019 Bail lift cam gear
Gear Assembly
C7769-60177 Paper drive transmission gear kit - Includes two gears used to drive the paper drive roller Part C7769-60177 is no longer supplied. Please order the replacement, C7769-60408
C7769-60408 Paper drive transmission gear kit - Includes two gears used to drive the paper drive roller
Guide
C4713-60184 Rollfeed guide kit - Left and right guides mounted under printer - Used to attach rollfeed housings to the printer
C7769-60179 Cutter guide - Guide bar for the cutter assembly - For 24-inch plotters
Motor
C4713-60092 Carriage motor assembly - Includes cable
C7769-60375 Carriage (scan-axis) motor assembly - Includes cable
C7769-60377 Paper axis motor assembly - Includes cables
Platen
C4713-60114 Entry platen assembly (D-size) - Curved cover/guide that is next to the paper drive (platen) roller
C7769-60155 Back platen assembly - Curved cover/guide that is installed below the paper drive roller (24-inches) Part C7769-60155 is no longer supplied. Please order the replacement, C7769-60410
C7769-60174 Front platen kit - Includes platens for both the 24-inch and the 42-inch models
C7769-60410 Back platen assembly - Curved cover/guide that is installed below the paper drive roller - For use with 24-inch plotters
Q5669-60155 Output platen assembly - For 24-inch plotters
Sensor
C4713-60034 Pincharm sensor assembly
C7769-60168 Media sensor Part C7769-60168 is no longer supplied. Please order the replacement, C7769-60379
C7769-60194 Pincharm sensor Part C7769-60194 is no longer supplied. Please order the replacement, C7769-60378
C7769-60378 Pincharm sensor - Installed in right front of print chassis
C7769-60379 Media sensor - Installed in the front of the rear platen
C7769-60384 Drive roller encoder sensor
Q5669-60675 Window position sensor
Spring
07575-80012 Bail gear support 'claw' spring - Attached between the bail engaging lever support and the bail gear assembly
C4699-00016 Encoder spring
C4713-80003 Pincharm spring
Carriage
Q6675-60043 Carriage rail oiler
Drive
CH538-67078 SATA Hard Disk Drive (HDD) - Includes firmware - For use with Designjet printers
Encoder
CH538-67073 Encoder disk - Helps provide position the information of the paper
Ink Supply Station
Q6683-60188 Left ink supply station - For the Designjet printers
Motor
CH538-67027 Media motor - For Designjet printers
CH538-67076 Scan-axis motor - For use with Designjet printers
Q6718-67017 Starwheel motor assembly - For Designjet priners
PC Board
CH538-67004 Formatter board - Does NOT include the Hard Disk Drive (HDD) - For the Designjet T1200 printer series
CH538-67009 Main PCA - Includes Power Supply Unit (PSU)
Pinch Assembly
Q5669-60705 Pinch lift assembly - Molded plastic part - Guides the paper during paper advancement
Power Supply
CH538-67011 Power Supply Unit (PSU) - For the Designjet T1200/T770 printer series Part CH538-67011 is no longer supplied. Please order the replacement, CR647-67010
Sensor
CK837-67020 Encoder sensor assembly - For Designjet printers Part CK837-67020 is no longer supplied. Please order the replacement, CR647-67023
Q5669-60666 Drop detector sensor assembly
Q5669-60706 Pinchwheel lifter sensor
Service Station
CH538-67040 Service station - Includes the drop detector and the service station spittoon - For the Designjet T1200/T770 printer series
Q5669-60667 Spittoon service station - For Designjet printers
Solenoid
Q5669-67807 Pen to paper space (PPS) solenoid - For Designjet printers
Spittoon
Q5669-67049 Left-side spittoon assembly - Holds expelled ink from cartridge during refresh cycle
Logic/Control Electronics
5188-6700 Universal AC power adapter - Separate AC power adapter with attached DC power cord - Requires country-specific AC power cord with C7 connector - 100-240VAC, 50/60Hz input, 12VDC, 1.25A output
Module
C4713-69203 Electronics module - Contains power supply, main logic board, interface connectors, and fan
C7779-60144 Electronics module - Contains main logic board, connectors for plug-in cards, connector for parallel interface cable, connector for USB cable, and cooling fan
C7779-60263 Electronics module - Contains main logic board, connectors for plug-in cards, connector for parallel interface cable, connector for USB cable, and cooling fan
C7779-69263 Electronics module - Contains main logic board, connectors for plug-in cards, connector for parallel interface cable, connector for USB cable, and cooling fan
PC Board
C7769-60441 HP-GL/2 and RTL formatter PC board
C7769-69441 HP-GL/2 and RTL formatter PC board
Power Supply
C7769-60387 Power supply assembly - Includes power switch
CH336-67012 Power supply assembly - For the Designjet 510 printer series Part CH336-67012 is no longer supplied. Please order the replacement, CH336-67014
Cable
CK837-67008 Left and right side harness cables - For Designjet printers
Cable Kit
CH538-67006 Cable kit - For the Designjet T series printers
CH539-67003 Cable kit - For the Designjet T770 printer series
Ink System Kit
Q6675-67004 Ink system purgers - Includes six units
Q6675-67005 Ink system purgers - Includes 100 units
Maintenance Kit
CH538-67024 Preventive maintenance kit 1 - Includes the carriage with cutter assembly, scan-axis motor, tube system with trailing cable, and belt - For the 44-inch Designjet T series printers Part CH538-67024 is no longer supplied. Please order the replacement, CR649-67003
Paper Path Module
Q6687-60093 Paper advance calibration kit - For 44-inch plotters
Tool
Q5669-60690 Flex contacts cleaning tool
Q6675-67017 Spanner tool
Q6675-67018 Media driver tool kit - Includes the handle for media driver tool support and the media driver adjustment tool
Q6683-67001 Tool kit - Includes pincwheel alignment tool, media driver tool, spanner number 13, oil dispenser, insert spring tool, tweezers, T15 screwdriver, 100cc isopropyl alcohol, lubricant oil, plastic gloves, flex contacts cleaning tool, and cleaning kit Part Q6683-67001 is no longer supplied. Please order the replacement, Q6683-67028
Q6687-60084 Pinchwheel insertion tool - For Designjet printers
Actuator
CH538-67064 Left and right side bumper cutter actuator - For the Designjet T series printers
Foam
Q6659-60182 Full bleed foam kit - For 44-inch plotters
Guide
Q6675-60044 Right side roll guide assembly Part Q6675-60044 is no longer supplied. Please order the replacement, Q6675-67026
Q6677-60019 Left side roll guide assembly - For 44-inch plotters
Lifter
Q5669-67054 Starwheel lifter assembly - For Designjet printers
Overdrive Assembly
Q6677-60018 Print zone overdrive assembly - For 44-inch plotters
Pinchwheel
Q6687-60085 Pinchwheel assembly - For the Designjet T series printers
Spindle
Q6687-67001 44-inch spindle assembly
Starwheel
CK839-67009 Starwheel assembly - For 44-inch plotters
Power Module/Recharger
0950-3358 Power module (Wall mount, MEI-AH ED12063) - Input voltage 240VAC, 47/53Hz - Output voltage 13VDC, 800mA, 10.4 watts (for use in Australia and New Zealand)
0957-2340 Power module (wall mount)- Input voltage 100-240 VAC - Output voltage 12 VDC, 15 watts
5188-5676 Power module (wall mount) - Input voltage 100VAC, 47/63Hz - Output voltage 13VDC, 800mA, 10.4 watts (for use in Japan)
Ink Tubes Assembly
C7769-60381 Ink tubes assembly - Includes 4 ink tubes complete with hardware assemblies at both ends (carriage crane and ink supply station crane), and 4 setup pens - For the 24-inch Designjet 500/800 printer series
Printhead
C7769-60164 Setup printhead kit - Used to prime the ink tubes - Includes 4 setup printheads
C9380A HP 72 Gray and Photo Black Printhead
C9383A HP 72 Magenta and Cyan Printhead
C9384A HP 72 Matte Black and Yellow Printhead
Bumper
CH538-67051 Left and right side upper roll support bumpers - For the Designjet T series printers
CH538-67052 Left and right side lower roll support bumpers - For the Designjet T series printers
Cover
CH538-67002 Lower roll cover assembly - With pinches - For Designjet printers
CH538-67003 Upper roll cover assembly - Includes pinches - For Designjet printers
CH538-67047 Roll cover bi-stable springs left and right - For Designjet printers
CH538-67050 Roll cover freewheel assembly - For Designjet printers
CH539-67009 Basic upper roll cover assembly - For the Designjet T770 printer series
Pincharm
CH538-67037 Pincharm assembly for roll cover - For the Designjet T1200 printer series
Sensor
CH538-67033 Single sheet sensor - For the Designjet T series printers
CH538-67041 Lower left support sensor with cable - For the Designjet T series printers
Spacer
CH538-67046 Left and right side wall spacers - For the Designjet T series printers
Support
CH538-67015 Upper left support - For the Designjet T1200/T770 printer series
CH538-67016 Lower left side support - For the Designjet T1200 printer series
CH538-67028 Upper right support - For the Designjet T1200/T770 printer series
CH538-67029 Lower right side support - For the Designjet T1200 printer series
CH538-67065 Upper left support sensor with cable - For the Designjet T series printers
CH539-67007 Upper left support - Without sensor - For the Designjet T770 printer series
Bin
CH639-69002 Media bin (Black) - Includes bin and support - Mounts to the printer stand legs
Q6659-60237 Media bin (Gray) - Includes bin and support - Mounts to the printer stand legs - For 44-inch plotters
Bracket
Q6712-69001 Foot bracket (Gray) - Includes two units Part Q6712-69001 is no longer supplied. Please order the replacement, CH539-69001
Cover
Q5669-60718 Leg cover - Slides down outside of stand legs
Cross-Brace
Q6659-60236 Cross-brace - Connects and supports the two stand legs - For 44-inch plotters
Foot
CH639-69001 Foot assembly (Black) - Includes two feet Part CH639-69001 is no longer supplied. Please order the replacement, CH539-69001
Hardware Kit
Q5669-60730 Hardware kit for printer stand - Includes screwdriver and screws - Used to assemble printer stand
Leg
Q5669-60716 Leg assembly - Side support for the plotter - Does NOT include the foot assembly
HP DesignJet T1200 CH538AR Plotter Ersatzteil - Liste