Bail
C4704-60329 Bail assembly - Mounting strip assembly for the starwheel mount assemblies (Not included) - Extends width of plotter
Bearing
1410-0708 Sleeve bearing - Used on left end of overdrive assembly
Belt, Zahnriemen, Antriebsriemen
C4704-60207 Carriage (Y-axis) belt - Drives the carriage assembly
Bin
C4704-60073 Media Bin Arm (Loop Assembly) - Wire Form Arms that Make Up Media Bin (4 Used)
Bracket
C4704-00005 Y-Axis Motor Bracket - Holds Y-Axis Motor - Includes Edge Wire Saddle
Brake/Housing
C4704-60199 Brake/housing assembly (on right side) - Accepts the flange end of the spindle rod assembly - Includes the 2 housing pieces, 2 brake shoes, brake gear, brake lever, and springs
Bushing
C1633-40082 Bushing - Retains Spring on Shaft of Pincharm Assembly
C3195-40076 Bushing - Attaches to Rear of Cutter Assembly - Connects Cutter Assembly to Slider Rod
C4704-40084 Rear Slider Rod Bushing (Spring Loaded) - Slides into the Rear Center of the Carriage Assembly
Cable, Kabel
C4704-60015 Trailing Cable - 3 Ribbon Cables from Carriage Board to Main Board, Flachbandkabel
C4704-60021 Hard Drive Power Cable - From Drive to Main Board
C4704-60022 Hard Drive Data Cable - From Drive to Main Board
C4704-60024 Service Station Interconnect Cable - Ribbon Cable from Service Station Interconnect Board to Main Board
C4704-60025 Refill Interconnect Cable - Ribbon Cable from Refill Interconnect Board to Main Board
Cam
C3180-40020 Pincharm Cam - Attached to Pincharm (Media) Lever
C3190-60149 Cam Jour l - Mounted on End of Pincharm Shaft (2 Used)
Carriage Kit, Schlitten, Druckkopf Wagen
C4723-69096 Carriage assembly - Includes carriage assembly, line sensor, encoder, rear bushing, calibration pen, digitizing sight, guages - Trailing cable and cable clamp not included REQUIRES RETURN OF DEFECTIVE PART(New part = C4723-60096)
Clamp
C4704-40085 Trailing Cable Clamp - Secures the Trailing Cable to the Carriage Assembly
C4723-40086 Trailing cable holder
Cleaning Supplies, Reinigungs Werkzeug
C6247A DesignJet cleaning kit - Includes cleaning solution and 20 cleaning rags
Cover
C4704-00004 MIO (Modular Input/Output) Cover - Mounted on Top of Electronics Module
C4704-00021 Top Cover - Covers Top of Plotter
C4704-00033 SIMM Cover - Covers SIMM Slots on Electronics Module
C4704-40057 Electronics Module Left Cover - Louvered Cover on Rear of Plotter
C4704-40058 Electronics Module Right Cover - Mounted on Rear of Plotter
C4704-40080 Encoder Strip Roof - Mounted in Carriage Assembly Over the Encoder Strip
C4704-60117 Line Sensor Lens Cover - Mounted on Carriage Assembly
C4704-60274 Electronics Module Cover - Mounted on Rear of Plotter - Includes SIMM Cover
C4704-60312 Rollfeed access cover - Opens forward to allow access to paper spindle assembly
C4723-60115 Right end cover - Has cut outs for the control panel
C4723-60116 Left End Cover (Cover meplate Mounts on)
Cross-Brace
C4704-60077 Cross-brace - Main structure that extends between stand legs
Cutter, Messer
C4704-60299 Cutter assembly - Auto cutter for rollfeed paper - Only for serial prefix ESA and ESB
C4723-60244 Cutter Assembly - Auto Cutter for Rollfeed Paper - Only for Serial Prefix>= ESC
Drive
C4724-69021 4.3GB Hard Disk Drive - Mounts in the Electronics Enclosure (This Drive Used as a Replacement for the Origi l 2.0GB Hard Drive) REQUIRES RETURN OF DEFECTIVE PART(New part = C4724-60021)
Elevator, Lifter, Aufzug
C4704-60033 Elevator platform assembly - Raises and lowers ink cartridges to fill the print heads - Located on left side of plotter
Enclosure
C4704-60067 Cutter enclosure - Mounted above entry platen
End Cap, Spindel
C2858-40043 Spindle End Cap (Small) (or Core Spacer) - on the Left End of the Spindle Rod - Removes for Loading the Media Roll
Fan, Lüfter See Description Cooling Fan is Part of the Electronics Module - Please Refer to Module
Firmware
C4723-69294 Firmware SIMM kit (Revision A.04.08) - Mounts in the electronics module - NOTE: this is not a postscript SIMM REQUIRES RETURN OF DEFECTIVE PART(New part = C4723-60294)
Flag
C4704-40007 Service station flag - Spring loaded flag on right side of service station
Foot
C4704-60086 Foot Assembly (Includes Casters) - Mounts to the Bottom of Left and Right Plotter Stand Legs (2 Used)
Front Panel, Bedienfeld
C4704-60255 Front (Control) panel and cable assembly - Includes function buttons and display
Gear, Zahnrad
C1633-40019 Cluster Gear - Mounts to the Left Side Plate of the Plotter - Between the Paper Drive Roller Gear and the Overdrive Gear
Gear Assembly
C4705-60089 Clutch / Overdrive Gear Assembly - Mounts Above the Cluster Gear on the Left Side Plate of the Plotter - Includes Gear, Clutch, Retaining Clip and Two Washers
Ground Strap, Masse
C4704-00016 Encoder ground strap - Provides ground to end of encoder strip
C4704-00035 Ground strap - Attached to Y-AXIS bracket
Guard
C4704-60295 Starguard Assembly - Covers the Starwheel Assemblies
Hardware Kit
C4704-60095 Hardware Kit - Used to Assemble Printer Stand - Includes Screw Driver, Screws, Washers and Media Bin Retaining Clips
Holder
C4704-60218 Quick Reference Holder Pocket - Holds Quick Reference Guides and Media Knife - Mounted on Rear of Right End Cover
Housing
C4704-60082 Housing Assembly (on Left Side) - Accepts the Left Side (End with Smaller End Cap) of the Paper Spindle Assembly
Humidor, Druckkopf
C6236A DesignJet CP ink system storage container - Holds printheads and printhead cleaners when not in use
Wartungs Kit
C4723-60141 Preventive Maintenance Kit - Contains line sensor cover, encoder strip, Y-AXIS pulley, belt, motor, cutter, silicon grease, plastic surface cleaner, synthetic oil and wipes
C4723-60238 Adjustment kit - Includes instructions, empty cartridge, digitizing sight (magnifier) and gauge
Leg
C4704-60075 Leg Assembly - Side Support for the Plotter (2 Used) - Does NOT Include the Foot Assembly
Lever, Sensor C4704-40059 Pinch arm (media) lever - Used when loading paper
Link
C4704-00025 Front Wire Link - Connected From Pincharm Cam to Spring Loaded Cam on Right Side Plate of Printer
Memory (Product)
C6229A 4MB SIMM Memory Module Upgrade
C6230A 8MB SIMM Memory Module Upgrade
C6231A 16MB SIMM Memory Module Upgrade
C6232A 32MB SIMM Memory Module Upgrade for DesignJet 400 and 700CP
Memory (SIMM)
1818-6171 4MB EDO (Extended Data Output) DRAM SIMM (C6229A)
C4723-60264 16MB EDO (Extended Data Output) DRAM SIMM (C6231A)
Motor C4704-60040 Bail Motor - Mounted on Left Side Plate
C4723-60277 Carriage (Y-Axis) motor assembly - Drives carriage belt - Includes motor, motor holder, and cable
C4723-60303 X-Axis Motor Assembly - Mounted on Right Side of Printer - Includes Motor, Belt, and Worm Gear - No Longer Supplied - Order X-Axis Motor Assembly Kit
C4724-60053 X-Axis motor assembly kit - New design does not use a belt - Kit includes motor with attached worm gear, helical gear, motor mount, screws and nuts for mounting the parts, grease for the helical gear, installation instructions
Mount
C1633-40089 Overdrive Mount Block - Installed at Both Ends of the Overdrive Assembly (2 Used)
Overdrive Assy C4704-60213 Overdrive Assembly - Mounted Between the Left and Right Side Plates of the Plotter Below Bail Assembly - For Serial Prefix ESA Only
C4704-60281 Overdrive Assembly - Mounted Between the Left and Right Side Plates of the Plotter Below Bail Assembly - For Serial Prefix>= ESB
PC Board, Elektronik Boards, Netzteil, Mainboard
C4704-60009 Refill Interconnect Board - Mounted on Left Side Plate of Plotter
See Description Power Supply and Main Logic PC Board are Part of the Electronics Module - Please Refer to Module
Pincharm
C4723-60247 Pincharm Assembly - Curved Black Plastic Plate with 4 Small Rubber Rollers (Does NOT Include Spring or Bushing) (7 Used)
Platen, Walze
C4704-60294 Entry Platen Assembly - Curved Cover/Guide that is Next to the Paper Drive (Platen) Roller
PostScript
C4704-69343 PostScript SIMM Kit - Version 8.1.01 - Installed in the Electronics Module - NOTE: This is not the Firmware SIMM REQUIRES RETURN OF DEFECTIVE PART(New part = C4704-60343)
Pulley, Umlenkrolle
C4704-60020 Idler pulley - For carriage (Y-axis) belt - On right end of plotter
Refill Assembly, Auffüll Station
C4723-60249 Refill assembly - Mounted inside the left hand cover - Includes motor and gears
Roller
C4700-60042 Paper Drive (Platen) Roller Assy - Long Gear Driven Roller - Includes Roller and Mark Encoder (Attached to Left End)
Saddle
0460-2536 Edge Wire Saddle - Installed in Y-Axis Bracket
Sensor
C4704-60029 Right End Cover and Window Closed Sensors - Includes Cable and Connector - Plugs Into Front Control Panel
C4704-60052 Pincharm Sensor - Mounted on Right Side Plate
C4704-60058 Left End Cover Sensor - Includes Cable and Connector - Plugs Into Refill Interconnect Board
C4704-60195 Media Sensor Assembly - Mounts to Right Side of the Entry Platen - Includes, Edge Measuring and Secondary Levers, Media Sensor and Holder
C4723-60096 Line Sensor - Mounted on Carriage Assembly - Detects Paper Width and Skew - Measures Calibration Accuracy and Printhead Alignment - No Longer Supplied - Order Carriage Kit
C4723-69071 Take-up Reel Sensor Assembly - Mounted Near Bottom of Right Leg REQUIRES RETURN OF DEFECTIVE PART(New part = C4723-60071)
Service Station, Reinignungs Station
C4723-60276 Service Station - Mounted on Right Side of Plotter - Holds the Print Head Cleaner Cartridge
Shaft
C2848-60032 Pincharm Shaft Assembly - Lever Actuated Shaft That Releases the Pincharms - Includes Cam Jour ls Mounted on Each End
Spacer
C4723-60147 Spacer/media guide for the supply spindle
Spindle, Achse für Rollen Papier
C4704-60317 Rollfeed spindle rod assembly - Includes flange and core spindle spacer
C6246-60010 Take-up Reel Spindle Assembly
Starwheel Mount
C4704-60143 Big Starwheel Mount Assembly (2 Used) - Includes: Cover, Body, Spring and Two Starwheels - Mounts on the Bail Assembly (Part Number is for One Starwheel Mount Assy Only)
C4713-60035 Starwheel Mount Assembly (11 Used) - Includes: Cover, Body, Spring and Two Starwheels - Mounts on the Bail Assembly (Note: Part Number is for One Starwheel Mount Assembly ONLY)
Strip, Encoder
C4704-40070 Capping strips - Two strips that s p together on the ends of the bin arms
C4704-60224 Encoder Strip - Used to Determine Carriage Position - Connects from Left to Right Side of Plotter
Support
C4704-40026 Roller Support Bracket - Installed on Left Side Plate
C4714-60147 Media Bin Support - Supports Media Bin Arms
C4723-60072 Take-up Reel Left Hand Support Assembly - Mounted on Left Leg
C6246-69009 Take-up Reel Right Hand Support Assembly - Mounted on Right Leg
Switch, Schalter
C4704-60056 Power switch - Includes cable
C4704-60261 Stand-By Switch - Mounted in Right End Cover
Take-Up Reel
C6246A Take-up Reel Kit - Includes Take-up Reel Spindle Assembly, Left and Right Take-up Reel Supports, Take-up Reel Sensor Assembly, Empty Core Tubes, and Media Weight Tubes
Tensioner, Umlenkrolle
C4723-60063 Y-Axis Tensioner Assembly - Applise Tension to Carriage Belt - Includes Wedge, Tensioner Spring and Housing
Tray
C4704-60084 Plotter Stand Tray - Mounted Between the Feet of Plotter
Tube Kit
C6246-60011 Media Weight and Core Kit - Used for the Take-up Reel
Window
C4704-60087 Lift-Up Viewing Window - on Top of Chassis
HP DesignJet 2500CP C4704A Plotter Ersatzteile